|
Item# |
Item |
Description |
Price |
|
|
1 |
 |
Thomson Linear Actuator for Sleeve lift
replacement
4 in stroke 600lb force all models all years.
100% compatible for older Bear
and Warner models.
12v 1/2" pin holes. The pin center to pin center retracted
measurement is 10-3/8". Used on our sleeve hitches. Not
recommended for the JBJr.
Note: Sorry, we cannot
accept any returns on actuators. Whether it's
a replacement for one of our products
or this is for a home built machine of your design, choose wisely. |
$300 |
|
|
2 |
|
Thomson Linear Actuator for Johnny Bucket lift all models all years.
4 in stroke 1200lb
force.
Johnny Bucket Jr lift replacement, all models all years.
100% compatible for older Bear and Warner models.
12v 1/2" pin holes. The pin center to pin center retracted
measurement is 10-3/8". Used on JBJr lift
Note:
Sorry, we cannot accept any returns on
actuators. Whether it's
a replacement for one of our products
or this is for a home built machine of your design, choose wisely. |
$300 |
|
|
3 |
|
Thompson Linear Actuator STD Dump ? Angle
6 in stroke 600lb force
STD speed Johnny Bucket Jr dump or plow angle replacement (not
compatible to replace with 2X turbo actuator)
100% compatible for older Bear and Warner models.
12v 1/2" pin holes.
The pin center to pin center retracted measurement is
12-3/8". Note:
The rear pin hole is rotated 90 deg. to what is shown in the picture.
Note:
Sorry, we cannot accept any returns on
actuators. Whether it's
a replacement for one of our products
or this is for a home built machine of your design, choose wisely. |
$320 |
|
|
4 |
|
Thompson Linear Actuator 2X
Turbo Dump / Angle
Turbo 2X speed Johnny Bucket Jr power
dump or plow angle replacement (not compatible to replace a STD
speed actuator) 100% replacement for older Bear and Warner models.
6 in stroke 600lb force 12v 1/2" pin holes.
The pin center to pin center retracted measurement is 14". Note:
The rear pin hole is rotated 90 deg. to what is shown in the picture.
Note:
Sorry, we cannot accept any returns on
actuators. Whether it's
a replacement for one of our products
or this is for a home built machine of your design, choose wisely. |
$335 |
|
|
5 |
|
Wire Harness Assembly w / toggle switch
Includes: inline fuse holder with 30A fuse, toggle switch and 5 ft of
wire to the actuator. just as seen |
$35 |
|
|
6 |
|
Replacement Control Harness
This is the same 5 ft control harness that is included
for JBJr's lift and power dump systems. |
$10 |
|
|
7 |
|
Replacement Power Dump and Plow angle Extension Harness
This is the same 27" dump extension harness that is included for power
dump and plow angle systems. Note: Since this harness has male
and female watertight ends, it can be cut in half and used as spliced in
pigtail replacements for the actuators or elsewhere. |
$8 |
|
|
8 |
|
1 Momentary Toggle switch only with boot
switch has built in reversing jumpers |
$12 |
|
|
9 |
 |
Pair of 2 Momentary Toggle switches with boots
switch has built in reversing jumpers |
$23 |
|
|
10 |
|
Momentary Rocker switch only
switch has built in reversing jumpers |
$13 |
|
|
11 |
|
Front weld mount pair 1/4in thick
|
$11 |
|
|
12 |
|
Rear weld mount pair 1/4in thick
|
$10 |
|
|
13 |
|
JBJr Bucket lift actuator pin kit with spacer bushings and clips
(Most models except L100 JD)
Kit includes (top to bottom)
1- 1/2 x 3 (+ quick clip) Top of lift actuator
1- 1/2 x 3 + (2- 1/2 spacers + cotter pin) Bottom lift actuator |
$10 |
|
|
14 |
|
JBJr Bucket pin kit with power dump actuator spacer bushings
Kit includes (top to bottom)
1- 1/2 x 2-3/4 + (1- 15/16 spacer + hardware) Rear dump actuator
1- 1/2 x 3-1/2 + (2- 3/4 spacers + hardware) Front dump actuator
2- 5/8 x 1-1/4 pins (+ hardware) Bucket pivot note: extra washer
used on power dump side. |
$17 |
|
|
15 |
|
JBSr Bucket pin kit
Kit includes (top to bottom)
2- 1/2 x 2-3/4 + ( + hardware) Rear of dump cylinder or bucket
2- 5/8 x 3 + ( + hardware) Front of dump cylinder or bucket
2- 5/8 x 1-1/4 pins (+ hardware) Bucket pivot |
$22 |
|
|
16 |
|
JBJr & Sr 1/2
Circle Clip
Used throughout all of our products |
$.25 |
|
|
17 |
|
JBJr & Sr 5/8
Circle Clip
Used throughout all of our products |
$.25 |
|
|
18 |
|
1/2" X 2" Clevis Pin 1-3/4" usable length (Use with weld mounts) |
$3 |
|
|
19 |
|
1/2" X 2-3/4" Clevis Pin 2-1/2" usable length (Use with LA U
bracket) |
$3 |
|
|
20 |
|
1/2" Bent Pin 3" usable length |
$3 |
|
|
21 |
+ 
|
Joystick
upgrade with adaptor harness and Box (Power Dump models only)
Add $95
Notes before purchasing: Plastic Enclosure for Joystick
Add $12
4-3/4" x 4-3/4" x 2-1/4" deep.
-
The joystick was made to be mounted behind a
dash panel or inside the box, not floating on top of the panel by itself.
(Yes, this should be obvious but it wasn't so now we have to mention it.)
-
If you're not sure if there's enough room on or
behind the dash, please get the box and play it safe so you can finish the
installation easily.
-
There are no designated places to install the
joystick upgrade. This upgrade is completely up to the installer to figure
out on there own. If you're not comfortable with this DIY (do it yourself)
option, please don't buy it and just use the included JBJr toggle switches.
-
If you want to mount it on the fender you
will need to lengthen your own wires. Our wires were made to get you up to
the dash in most cases.
-
We wish we had examples of installations for
all the models we sell for but sorry we don't. There are hundreds of ways to
do it.
|
$115 |
|
|
22 |
|
Joystick
upgrade with adaptor harness (Power Dump models only)
Add $95
Notes before purchasing:
-
The joystick was made to be mounted behind a
dash panel or inside the box, not floating on top of the panel by itself.
(Yes, this should be obvious but it wasn't so now we have to mention it.)
-
If you're not sure if there's enough room on or
behind the dash, please get the box and play it safe so you can finish the
installation easily.
-
There are no designated places to install the
joystick upgrade. This upgrade is completely up to the installer to figure
out on there own. If you're not comfortable with this DIY (do it yourself)
option, please don't buy it and just use the included JBJr toggle switches.
-
If you want to mount it on the fender you
will need to lengthen your own wires. Our wires were made to get you up to
the dash in most cases.
-
We wish we had examples of installations for
all the models we sell for but sorry we don't. There are hundreds of ways to
do it.
-
There is more information at this link more
information
|
$95 |
|
|
22 |
|
Plastic Enclosure for Joystick
Add $17
4-3/4" x 4-3/4" x 2-1/4" deep.
Can be mounted on the side of the dash with the 4-3/4" x 4-3/4" facing you. It
could also be mounted on a fender. Note: (if mounted on the fender, you will
need to lengthen the wires yourself)
|
$17 |
|
